90W constant voltage 12V DALI DT8 dimmable driver for led strip lights
1. Description
-Flicker-free for the whole dimming range
-Stand-by power below 0.5W
-Primary dimming with a push button
-Secondary dimming with 0-10V dimmer and potentiometer
-Built-in DALI interface DT8
-Supports 10V PWM dimming (3KHz-8KHz)
-Protection: short circuit / over temperature/ over voltage
-Derating the current for high ambient temperature
-Push dim with memory function
-5-year warranty
2. Parameters
| Series | Name | KL90VC-PDiiV |
| Input | Voltage range | 198~264Vac 50Hz /60Hz |
| Rated supply voltage | 220~240Vac 50Hz /60Hz |
| DC voltage range | 200~240Vdc |
| Input current (@230Vac) | 0.46A Max |
| Inrush Current | 30A (Half current pulse width 100US) @230VAC |
| Power factor | ≥ 0.99 (@230Vac,100% load) |
| Total harmonic distortion | Typical: 6% (@230Vac, 100% load) |
| Stand-by power | ≤0.3W |
| Efficiency(230Vac,100% load) | 91%Max |
| Wiring method | Push terminal, wire cross section:0.5-1.5mm2 |
| Loop-in&Loop-out quantity | 16PCS(@230Vac) |
Automatic circuit breaker type
(Calculate current in the wire) | B10 | 7 | C10 | 12 | B10 | 7 | C10 | 12 | B10 | 6 | C10 | 10 |
| B13 | 9 | C13 | 16 | B13 | 9 | C13 | 16 | B13 | 7 | C13 | 13 |
| B16 | 11 | C16 | 20 | B16 | 11 | C16 | 20 | B16 | 9 | C16 | 16 |
| B20 | 14 | C20 | 25 | B20 | 14 | C20 | 25 | B20 | 11 | C20 | 20 |
| B25 | 17 | C25 | 35 | B25 | 17 | C25 | 35 | B25 | 14 | C25 | 25 |
| / | / | C32 | 35 | / | / | C32 | 35 | / | / | C32 | 30 |
| Output | Operating mode | Constant voltage |
| Load type | LED |
| Flickering / Flickering-Free | Flickering-Free |
| Start-up time | <1s (@230Vac) |
| Forward voltage | 12V |
| Output current | 7.5A |
| Max. output voltage (no-load ) | 20V |
| Full load output power | 90W Max. |
| Minimum load | 9W |
| Output | Output current/voltage tolerance | ±5% |
| Wiring method | Screw terminal, wire cross section:2*0.5-2.5mm2 |
| Control Method | Primary PUSH Dimming | Primary PUSH dimming (Max. lead wire length:20m) |
| 1-10V(0-10V)Dimming | 0-10V dimming(Port current＜1mA),
(Max. lead wire length:20m) |
| Dimming Range | 0%-100% |
| Secondary PWM dimming | 0-10V port PWM dimming (3KHz-8KHz) |
| Potentiometer | Yes, 100kΩ |
| DALI function | DALI dimming (Max. lead wire length:300m) |
| Exception Protection Requirements | Output over temperature
protection | Yes, reset power on to recover |
| Output short circuit protection | Yes, reset power on to recover |
| Operating Environment | Storage temperature/ humidity | -40℃~80℃, Humidity:10%–95% |
| Operating temperature/ humidity | -25~50℃ |
| Max. case temp(Tc) | 85℃ |
Safety
& EMC | EMC standard | EN55015, EN61547, EN61000-3-2, EN61000-3-3 |
| DALI standard | IEC62386-101 / 102 / 207 DT6 / 209 DT8 |
| Safety standard | EN61347-1, EN61347-2-13 |
| Certification | CE |
| Withstand voltage | 3750Vac, 5mA, 60s (Input “L N”- Output “SEC”) |
| Others | IP Rating | IP20 |
| Type of protection | Class II |
| Installation type | Independent installation |
| Installation dimension | 202*58*30mm |
| Memory function | Yes, (PUSH with memory function) |
| PUSH dimming synchronization | Parallel: 15 units Max. Series: 25 units Max. |
| Packaging requirements | Instruction+clapboard+outer carton(K=A) |
| Weight | 400g |
| Life | 5 years @Ta 100% load |
| Note: All parameters are tested at the input voltage of 230VAC and a 25-degree environment unless specified. |
3. Dimension (Unit: mm)
4. Wiring Diagram
Fig. A DALI Dimming
Fig.B Push Dimming
Fig.B 1-10V Dimming
5. Derating
6. Dimming curve
7. ON/OFF & Description of Dimming Operation
A. Short-press the PUSH switch (short-press time 0.1s-1s), the LED driver will turn on or off.
B. Dimming:
Press and hold the PUSH switch (1s-8s), the LED driver can achieve dimming, brightening, or dimming, the dimming range is 2-100%.
C. Color temperature adj:
Step 1, PUSH turns off the lights; Step 2, press and hold PUSH to adjust the color temperature starting from the current brightness; Release PUSH, press and hold PUSH again, and adjust the color temperature in the opposite direction; No operation for 5 seconds, exit color adjustment mode.
D. Memory:
PUSH dimming has a dimming memory function.
E. Dimming synchronization:
The power connected to the same PUSH switch can be synchronized by pressing and holding the PUSH switch for longer than 15s
F. DALI dimming mode:
Connect the power supply to the DALI system, and it can be dimmed by the DALI host. The dimming range is 0-100%.
G. Constant voltage dimming drivers cannot be used in lamps with constant current circuits.
Product Tags:
|
|
90W constant voltage 12V DALI DT8 dimmable driver for led strip lights Images
|
